pics

Discussion in 'Equipment, Tools & Vehicle Pictures' started by cameo89, Feb 20, 2008.

  1. cameo89

    cameo89 Senior Member
    Messages: 667

    Here a few pics of last week, we had about 6-8''

    resize 1.jpg

    resize 2.jpg

    resize 3.jpg

    resize 4.jpg
     
  2. NBI Lawn

    NBI Lawn PlowSite.com Addict
    Messages: 1,796

    Wow, you already swapped the plow back to the Dodge
     
  3. OP
    OP
    cameo89

    cameo89 Senior Member
    Messages: 667

    Ya, I did that the morning that the trany went out, only took me 90 mins to pull complete harness & undercarriage (push beam only) & re-install all on Dodge, air tools & heated garage helps alot.wesport

    Yon
     
  4. AbsoluteH&L

    AbsoluteH&L Senior Member
    Messages: 566

    Are you trying to sell the Chevy, or bury it under the snow pile.:D
     
  5. OP
    OP
    cameo89

    cameo89 Senior Member
    Messages: 667

    As long as I don't cause any damage and can open the door, I can get it out ''It's a Chevy''
    I just pulled it out today to remove some tools and such.


    Yon
     
  6. BRAAAP

    BRAAAP Senior Member
    Messages: 114

    looks great!!!! wish we had some snow to push:cry: hows he 1500 handle the boss going to put either a boss or blizzard on mine next year to replace the sno way
     
  7. Supper Grassy

    Supper Grassy Senior Member
    Messages: 947

    looks good
     
  8. OP
    OP
    cameo89

    cameo89 Senior Member
    Messages: 667

    I would much rather push w/ my Dodge only cause it's newer (Love my heated mirrors) but the Chevy holds the weight better & pushes better, If I were you I would put a Boss Plow on for sure!

    Yon
     
  9. deere615

    deere615 2000 Club Member
    Messages: 2,913

    Nice trucks
     
  10. jce4isu

    jce4isu Senior Member
    Messages: 289

    can you take pics of the wings i want to put them on my boss poly
     
  11. OP
    OP
    cameo89

    cameo89 Senior Member
    Messages: 667


    heres a link to a thread that I started on ''Wings on a Poly'' I installed the same way every one else does W/ maybe a little more labor involved
    I had to cut the back brace to fit snug w/ cross brace & I plan to weld it to the cross brace and run a peice of angle across the top as extra support

    http://www.plowsite.com/showthread.php?t=56068&highlight=wings+poly
    Hope this helps & Good luck on your project

    Yon

    100_0158.jpg

    100_0159.jpg

    100_0160.jpg

    100_0161.jpg
     
  12. jce4isu

    jce4isu Senior Member
    Messages: 289

    thanks that helps im going to get a set 4 mine
     
  13. Quality SR

    Quality SR PlowSite.com Addict
    Messages: 1,832

    You got that right. It is triple that with out the air tools and the garage. Nice trucks.
     
  14. Quality SR

    Quality SR PlowSite.com Addict
    Messages: 1,832

    You did a good job on those wings. How is the poly holding up around the holes? Any stress cracks?
     
  15. OP
    OP
    cameo89

    cameo89 Senior Member
    Messages: 667


    Seems to be holding up good (no cracks) other than I keep loosing nuts & bolts for my wings
    I have replaced 2 of them once and I am missing 2 right now, next time locking nuts.

    Yon
     
  16.