Snow Plowing Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 21 Results
  1. Chevy Trucks
    Not sure if I’m posting in the right section. I’m looking around for a plow for my 2013 Sierra 1500, I’m planning on using a 7.6 fisher plow I’ve seen a lot for sale in my area but I’m looking for push plates. I’m not trying to cheap out but no one is selling the push plates. I’m looking for...
  2. Fisher Engineering Discussion
    The last plows I used had headgear and push plates on the truck and the plow was separate. I now have a 19’ F-250 and need truck side equipment. What versions of Fisher will the push plates accept?
  3. Truck & Equipment Repair
    Hello All! I’m new to the forum. After plowing for 16 yrs (1986-2002) I have come back to plowing again and so much has changed since the older style plows and truck side push plates and frames. In the past I had 8’ Fisher on a 86’ 3/4 ton GMC and in 1997 I put a 9’ Diamond on a 97’ Dodge 2500...
  4. Used Plowing and Truck Equipment Forum
    Looking for a set of used Fisher 7189 push plates. They are for a 2012 Ram 1500. Thank you
  5. Chevy Trucks
    I have a 06 3500. Does anyone know if push plates and wiring will Fit my truck that came off a 06 2500 ? Also, do push plates from other years fit my truck. Thank you !
  6. Used Plowing and Truck Equipment Forum
    Hi, I have an older 8" Fisher speedcast plow that came off a 73-87 GM but, I need a Fisher truck mount to fit my 1987 F-250. (I think a 1980-1991 Ford F-250 or F-350 mount will work) but it has to be the old "speedcast" style (NOT A MINUTE MOUNT) The blue colored areas in the photo are the...
  7. Fisher Engineering Discussion
    I have an HT Series Fisher plow that came off of my 07 GMC Sierra. I want to install it on one of these trucks you see at the dealership which already have the lift kit installed. Rocky Ridge Etc. The truck I'm interested in has a 6 inch lift and 35 inch tires. I clearly understand the...
  8. Fisher Engineering Discussion
    I recently bought a fisher 6.5 minute mount for my blazer. They dont make that plow anymore and never made push plates for my blazer! Any suggestions or ideas to help me get going this winter??
  9. Truck & Equipment Repair
    I'm trying to find fisher minute mount push plates for a 2000 silverado. The fisher # I was given is 7160 but I was just told that 7168 would also work but just sticks out a little bit farther. Anyone know if this is true? And if it is, how much farther do they stick out? If anyone has used...
  10. Used Plowing and Truck Equipment Forum
    I have an 08 f350 and I am looking for all or some of the parts listed below. Push plates #7183. Controller #49800 or 29800. Headlight harness #29049 Module #29760-1 Shoes #26523 Thank you very much!
  11. Used Plowing and Truck Equipment Forum
    I need a set of push plates for my 2008 Ford Super Duty. I am located in MN. I also have a set of 7176 push plates for 2005-2007 Super Duty for sale or trade. $350 for the 7176. Thanks!
  12. Used Plowing and Truck Equipment Forum
    Very nice Fisher Minute Mount 2 push plates for 2005-2007 Super Duty. All mounts and hardware. I am in need of 7183 or 7183-1 push plates for my 2008 Super Duty, willing to trade. $350
  13. Truck & Equipment Repair
    Hello, I am new to this site and hope that someone here can help me with the following issue. I recently purchased a used Fisher plow for my driveway. After getting it home and looking up the install instructions on the Fisher site I find that Fisher made two different push plates for the...
  14. Chevy Trucks
    I have a 1995 GMC Topkick LoPro i'm looking for a 9' plow or bigger any help would be greatly appreciated. i do have a budget of around 2500 max if possible. Thanks. I'm located around Sebago lake Maine e-mail me with what you got.
  15. Used Plowing and Truck Equipment Forum
    currently mounted on 01 gmc sierra Push plates all wiring just no stick Looking for best reasonable offer Located in Rhode Island Will consider shipping buyer pays .
  16. Used Plowing and Truck Equipment Forum
    I'd prefer a used set rather than new - trying to save a few dollars over the $500 list price for these things. I only plan on using the truck for my own personal nothing fancy is needed. A set that needs a little grinding/welding and paint work is OK by me. Let me know what you...
  17. Chevy Trucks
    hi im new to the site and was wondering if it is possible to modify push plates from a 1984 chevy half ton to fit a 1994 chevy half ton? im asking because i just got a complete set up and the equipment came off of a 1984 and i would like to avoid buying new plates if i can. thanks!
  18. Fisher Engineering Discussion
    is it required to remove the bumper off of my 2001 ford f250 to install fisher minute mount push plates? i know the directions say so, but didnt know if there was another trick. if you must take it off, does anybody know any hints on an easy way to do so? any help/pictures are greatly...
  19. Used Plowing and Truck Equipment Forum
    just found the plated on ebay and bought them. is there suppose to be a beam between the plates?
1-19 of 21 Results