Snow Plowing Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 88 Results
  1. Ram Trucks
    I recently purchased a used 8’ Meyer Lot Pro EZ mount. I am planning to mount it on my 93’ W250 w/12v Cummins and 5-speed manual. I tried to find a bolt on mount kit through Meyer but the website won’t let me configure the plow for my truck, so I will have to modify/fabricate the kit that came...
  2. 🔧 Truck & Equipment Repair
    I was plowing the last storm, was in the truck about 5 hours then plow suddenly stops working and just clicking no left,right or up function, down function works. I replaced truck side solenoid and red and black on the pump side and no Luck it’s still clicking. Anyone have ideas of what’s going...
  3. Chevy Trucks
    I just picked up a 1999 Chevy Silverado 2500 with a Meyers C-7.5 mould-board, E-57 pump, what looks like an MDII mount setup with Nite-Sabre (not the Sabre II) plow lights, using 07347 light control modules (newer-style with accessible fuses). The plow mechanics and controller work like a dream...
  4. 🔧 Truck & Equipment Repair
    Hi everyone, first post here. I’ve been having an issue with my meyer e-58h plow . It started with the left and right not working or holding pressure. Mechanic pulled the bypass valve and there was a white, hard piece of plastic stuck in the valve. Disassembled the valve and removed it and...
  5. Meyer / Diamond Products Discussion
    I ended up with a meyer classic hoop style plow i own a 2010 f250 modded a 2008 f250 mount Question is 8 1/4" ground clearance to the bottom of the mount good enough? It does not sag more then 1/2 when plow is on it.... I wanted to get some input while my buddy still has his welder out...
  6. Meyer / Diamond Products Discussion
    Hello all! I'm looking for the installation manual to put a 18522 Meyer mount on a Mitsubishi L200. It didn't come with any instructions at all. I tried googling it and nothing comes up. I contacted Meyer and haven't gotten a response after a few days now. Where else can I look?
  7. 🔧 Truck & Equipment Repair
    I am trying to install the electrical for a meyer plow on a 2015 silverado. I am currently unable to get power to the the pistol grip. Here's what i have done so far: -All wires have been run from the bumper to the battery and under dash - The 2 red wires from the headlight module are connected...
  8. Meyer / Diamond Products Discussion
    Hey guys, I just bought a plow truck with a Meyers 7 1/2 blade with an E47 pump set-up. So the plow moves up and down just fine. It does not move side to side under its own power. I replaced the A, B, C coil and valves thinking it would be a bad valve/coil and to make me feel stronger about not...
  9. Used Plowing and Truck Equipment Forum
    I'm looking for a Meyer classic plow mount for a 1992-1996 F150. Meyer part # 17097... Thanks M.E.M.
  10. Government Property Snow Removal
    My brother and I recently purchased two plows from an Indianapolis International Airport employee. According to him these two plows, an 8ft. and an 11ft., were retired from airport service. We are trying to identify the smaller of the two. We believe it is a Meyer ST plow however we are not...
  11. Meyer / Diamond Products Discussion
    I have a Meyer E72 Lot Pro 8 that will not angle left or right. The plow lifts up and goes down. The pump runs clicking left or right and it appears the rams are trying to work, but something is stopping them. They did work normally for a few seconds today, but the other 4 hours they did not...
  12. Meyer / Diamond Products Discussion
    Hello, I have a Meyer E60 that will not stay raised (slowly leaks straight down) and will not turn right. Every once in awhile while raising it turns left, but rarely. I spent all day today going through the Meyer troubleshooting manuals online but was unable to solve these issues. Any ideas...
  13. 🔧 Truck & Equipment Repair
    Wondering if I can get a little guidance on pin-pointing an issue I'm having with my Meyer E57. I was plowing snow for a solid 2 hours with no issues. But as i pushed snow into a pile, not hard or anything unusual, the plow kinda angled a little more then I had it. After that the plow would not...
  14. Used Plowing and Truck Equipment Forum
    I have a nice Meyer 8'-6" plow for sale newer edge newer angle cylinders newer motor on E60 pump Sabre II lights wiring harness Mount and Hoop for 92-97 F250
  15. Used Plowing and Truck Equipment Forum
    For sale: Meyer plow mount for Dodge Ram. Came of a 2006 4500. Does not include the clevis. Asking $295. Located in southwest Ohio. Pickup or I can ship cost based on zip code.
  16. Meyer / Diamond Products Discussion
    He y guys. I'm installing an EZ Mount Plus on a @017 Tundra. The instructions say to ream the rear hole on the from on the outside for an 11/16 sleeve. The instructions do not state anything about reaming the inside hole. However the sleeve does not fit through the inside hole. In my mind the...
  17. Meyer / Diamond Products Discussion
    Hey guys. I'm installing an EZ Mount Plus on a 2017 Tundra. My question is, The instructions say to bore the outer rear hole in the frame for 11/16 sleeve, However the inner hole is small as well. The instructions do not say to bore inner side of frame. To me it would seem that the sleeve should...
  18. Used Plowing and Truck Equipment Forum
    i have a Meyer 8.5 super v for sale. Price includes mount, harness, handheld controller, and plow. Plow is barely 2 yrs old it came on the truck and we run westerns so selling it as a complete. Everything works and according to the owner and the dealer is still under warrantee. Prior owner used...
  19. Commercial Snow Removal
    Hi all, I have been lurking on the site for awhile but thought I should finally make a thread. I am in the market for a new plow currently running a older 2005era blizzard power plow weighs in about 970lbs. I am not a huge fan the only thing I enjoy about it is the strap on center console...
1-19 of 88 Results
Top