Snow Plowing Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 203 Results
  1. 🔧 Truck & Equipment Repair
    My husband has a Fisher minute mount 2 8' straight plow on a 2019 dodge ram 1500 with air bags. He was plowing earlier and the blade dropped and wouldn't turn to the right or left. He was able to limp it home and has been fighting with it in the driveway for the last 5 hours...... It's snowing...
  2. Fisher Engineering Discussion
    I have a MM1 plow with a 3 plug setup. I have the harness and the iso module but not the wiring for the lights. I was sold a 29400-7 wiring harness kit from the dealer. The manual for the 29400-7 only shows wiring for 2 plug plows. Is this going to be a problem?
  3. Fisher Engineering Discussion
    I have a fisher stick controller hooked up to a MM1. It is current getting accessory power from an "add a connection" in a fuse socket. Will the controller light up if it is getting keyed power or does the harness have to be hooked to the plow?
  4. Fisher Engineering Discussion
    Fisher MM1 on an 09 Chevy 1500. I don't have the correct harness for the lights. I have the rest of the harness controller and isolation module. Can I get the plow to work without the lights hooked up? Is there some alternative wiring I need to do?
  5. Used Plowing and Truck Equipment Forum
    2009 Ford F350 PLOW TRUCK, dump body does not work though all parts are still there. 41,500 miles. 9 ft Fisher MM2 with Fishstick controller. Truck runs, drives, stops and plows. Roof strobe (LED) included. Bed needs work (have tailgate to the truck), exhaust needs work (manifolds). Questions...
    $15,000 USD
  6. Used Plowing and Truck Equipment Forum
    2009 Ford F350 PLOW TRUCK, dump body does not work though all parts are still there. 79,000 miles. 9 ft Fisher MM2 with Fishstick controller. Truck runs, drives, stops and plows. Roof strobe (LED) included. New tires, rotors, pads & calipers. Bed needs work (have tailgate to the truck), exhaust...
    $14,000 USD
  7. Introduce Yourself to the Community
    Hello I’m looking for some help with my Fisher MM1 3 plug plow. I plugged in my plow and as soon I pressed raise it turned right, I pressed left and it still turned right. I pressed right and it went right. Not sure what the problem could be, I pulled out the 3 pump valves/ solenoids and cleaned...
  8. Fisher Engineering Discussion
    Hello everyone, so I made a huge oopsie this morning, I won't get into detail as to keep the thread short. I have a fairly new I believe 2018 or 19 Fisher Polycaster, the fleetflex dual motor one. Basically this morning I ripped the spinner assembly off the back and it fell off on the road... I...
  9. Fisher Engineering Discussion
    Hey everyone, so I made a huge oopsie this morning... I won't get into the exact how so we can keep this thread short... I have a newer 2018 I think, Polycaster the dual motor one. And I accidentally ripped the spinner off the back this morning and lost it on the road... Picked up no visible...
  10. 🔧 Truck & Equipment Repair
    Has anyone ever or can you leave your tailgate on a pick up truck with a 1.5yd polycaster in the bed?
  11. 🔧 Truck & Equipment Repair
    Hello everyone. I’ve got an older fisher mm1 I’m having issues with. The plow is new to me and I don’t know much about its past. It is struggling to lift the blade and even sounds like it’s having a hard time angling side to side. The motor sounds like it’s bogging down and it doesn’t sound as...
  12. Fisher Engineering Discussion
    I have a 18 or 19 polycaster I'm looking for some tips on, I haven't had to do much since I bought it, it's been very reliable. In the winter I spray it out well when I wash the truck which I try to do atleast once a week if the weather permits (have to wait for warm days since I don't have a...
  13. 🔧 Truck & Equipment Repair
    Hello everyone. I recently purchased a MM1 plow for my 2002 f350. I’m having an issue where is moves slowly side to side. Up and down seems to be working fine. I would say it takes about 12-15 seconds to go from full left to full right. It’s moves slowest when it’s angled farther and slowly...
  14. Ice Management
    I have a 18-19 fisher poly-caster the fleetflex model, I just made a post back around November asking how to install strobes and a spare vibrator I had laying around, well I got them installed and wired up through the fisher harness. The strobes work great, but I'm having I think an issue with...
  15. 🔧 Truck & Equipment Repair
    I have a 2 yard Downeaster has electric spreader. The clutch will engage and spin and then shuts off on it on, continually. I reprogrammed a new controller, checked and cleaned all wiring and grounds, greased all chains. I can’t keep the clutch engaged and running. I assume the clutch is fine...
  16. Ram Trucks
    need some help. i have a fisher flex plow with a 3 port module. tried to wire a set of led plow lights to it but only thing that works is the high beams. not sure where i'm going wrong. where do my com wires go?
  17. 🔧 Truck & Equipment Repair
    Hello everyone. I recently bought a 2021 Ford F250 with the 6.2L gas job. The truck has a snow plow prep package but only has a single battery. I have a Fisher XV that I plan to use this winter. A buddy of mine has a 2019 f350 single battery 6.2 like mine with the XV2. He told me that when he...
  18. Fisher Engineering Discussion
    Hi everyone. I recently bought a 2021 F250 and put my Extreme V plow on it off my old truck. I mounted the push plates and wired everything myself. There was a small wire, that was supposed to get keyed 12 V power, that was connected to my four pin in cab controller harness. Because I have the...
  19. 🔧 Truck & Equipment Repair
    Hi all. I minute mount 2 wire setup on an older 99 ram 2500 truck. I brought it to a reputable fisher dealer in my area to install mount and wires to make it work on my 2014 ram 3500. He told me no problem will be done in a few days. He then calls me multiple times saying I need to buy this and...
  20. Ice Management
    I have a Fisher poly caster I bought in 2019, I'm looking to install strobes and a vibrator on it. I would rather not buy them from Fisher as they are pretty over priced if you ask me haha, I mean 400$ for the strobe kit? Who knows how much for the vibrator kit. I have a few extra slim strobes...
1-20 of 203 Results
Top