1. Welcome to PlowSite. Notice a fresh look and new features? It’s now easier to share photos and videos, find popular topics fast, and enjoy expanded user profiles. If you have any questions, click HELP at the top or bottom of any page, or send an email to help@plowsite.com. We welcome your feedback.

    Dismiss Notice

Toro ccr 2450 help

Discussion in 'Truck & Equipment Repair' started by lawnkid14, Dec 11, 2011.

  1. lawnkid14

    lawnkid14 Member
    Messages: 56

    Hello I have a newer toro ccr2450 with the rtek motor. It wont idle all it will do is build up rps really fast until auger is engaged again. I just cant seem to figure it out hope you guys can help me out before the snow really starts coming.
     
  2. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    Is that a 2 stroke or 4 stroke motor?
     
  3. WIPensFan

    WIPensFan PlowSite Veteran
    Messages: 3,495

    Should be a 2 stroke. I believe it's the blade governor. It's located behind the pull chord and engine cover. quite a bit to take apart to get to it. Could just be sticking.
     
  4. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    True,,could. I'm thinking more simple tho. Ff, carb bowl. Bad gas
     
  5. WIPensFan

    WIPensFan PlowSite Veteran
    Messages: 3,495

    I'm no expert, but I've had one do the same and narrowed it to that.
     
  6. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    Usually that's it. Just remember KISS. 99% of time its gas/gas filter and plug .
     
  7. lawnkid14

    lawnkid14 Member
    Messages: 56

    its a 2 stroke so it could be that blade fin, why would it be that fin any how. it works fine under load.
     
  8. cet

    cet PlowSite Fanatic
    Messages: 7,202

    Did you put stabilizer in the fuel before you put it away. I bet the carb is all gummed up.
     
  9. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    Try plug, Ff, and drain and fresh gas.
     
  10. Brian Young

    Brian Young PlowSite Veteran
    Messages: 3,382

    Mine did the same exact thing this year and I put stabil in, cleaned carb, took apart the carb, fresh fuel, new filter and it still does it so I would say the paddle gov. as well.
     
  11. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    You should be able to move the gov. Without taking apart the cover. Just to see if its free, if the arm doesn't move then yea is say that's your problem.
     
  12. lawnkid14

    lawnkid14 Member
    Messages: 56

    Could it be that spring as well I remember it being all twisted and worn
     
  13. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    At the carb?? The spring that runs in the linkage? Or the spring that goes to the arm ?
     
  14. lawnkid14

    lawnkid14 Member
    Messages: 56

    Well its the spring that is attached to a plate that can be adjusted and then it foes to the carb
     
  15. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    Yea. Start there replace that. That could be the main issue .
     
  16. lawnkid14

    lawnkid14 Member
    Messages: 56

    If that isn't it what could it be then
     
  17. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    If you have twisted and mangled parts,,,start there. That could be half/only problem you have remember KISS
     
  18. lawnkid14

    lawnkid14 Member
    Messages: 56

    Also i removed that fin everything looks to be good and is moved freely

    bump to top
     
  19. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,969

    K replace spring then, Ff , plug, drain gas fresh, take off carb bowl and clean.
     
  20. lawnkid14

    lawnkid14 Member
    Messages: 56

    ff means fuel filter right