1. Welcome to PlowSite. Notice a fresh look and new features? It’s now easier to share photos and videos, find popular topics fast, and enjoy expanded user profiles. If you have any questions, click HELP at the top or bottom of any page, or send an email to help@plowsite.com. We welcome your feedback.

    Dismiss Notice

Plow On 6420 JD

Discussion in 'Equipment, Tools & Vehicle Pictures' started by Cover Guy, Jan 4, 2010.

  1. Cover Guy

    Cover Guy Senior Member
    Messages: 224

    I Just Finished Putting A Old 10' Township Plow On A 6420 Deer Hooked The Hydraulics up To The Loader Joystick Every Thang Turned Out Better Than I Expected

    100_0284.jpg

    100_0285.jpg

    100_0283.jpg

    100_0282.jpg

    100_0281.jpg
     
  2. BMWSTUD25

    BMWSTUD25 Senior Member
    Messages: 630

    LOOKS GREAT!! Sharp looking tractor
     
  3. jomama45

    jomama45 PlowSite.com Addict
    Messages: 1,172

    Nice set-up. I really like the plow!! :salute:

    Did that plow originally have a single chain set-up though?

    Also, I think you may want to think about increasing the pin size IF they're only 1".
     
  4. JohnnyRoyale

    JohnnyRoyale 2000 Club Member
    Messages: 2,935

    Good luck with that setup.

    Won't comment on how its fastened to the machine-JD-waddya think?
     
  5. sno commander

    sno commander PlowSite.com Addict
    from ct
    Messages: 1,061

    looks good those are popular tractors in this area great for hay
    the only thing i would have done different is where the angle iron meets the flat steel on the tractor i would have ran it a little longer to catch that bolt but as long as your welds are good i think it will work great. good fab work :drinkup:
     
  6. Cover Guy

    Cover Guy Senior Member
    Messages: 224

    well if we need to we can increase them, originally the plow was a vertical lift so we added the chain
     
  7. Cover Guy

    Cover Guy Senior Member
    Messages: 224

    thanks i am pretty confident i wont have any problems with the welds
     
  8. Cover Guy

    Cover Guy Senior Member
    Messages: 224

    how would you have fastened it?
     
  9. JD Dave

    JD Dave PlowSite Fanatic
    Messages: 11,045

    Our subs 7810 is pretty much has the same mount on the tractor and he's been using it for almost 7 years like that with 14ft so I think it should work well. My only concern is where the blade mounts to the harness, that could be a weak point. Good luck It sgould make a great snow plowing machine.
     
  10. SuperdutyShane

    SuperdutyShane PlowSite.com Addict
    Messages: 1,517

    Looks good. Good luck with it.
     
  11. JD Dave

    JD Dave PlowSite Fanatic
    Messages: 11,045

    BTW Put a cross over releif valve between the angle cylinders.
     
  12. Cover Guy

    Cover Guy Senior Member
    Messages: 224

    Thanks For The Info
     
  13. mike6256

    mike6256 Senior Member
    Messages: 286

    WOW, thats a nice driveway machine :laughing: just kidding looks GREAT!!
     
  14. Pushin 2 Please

    Pushin 2 Please PlowSite Veteran
    Messages: 4,569

    That won't have any trouble moving some snow. Good luck!
     
  15. JohnnyRoyale

    JohnnyRoyale 2000 Club Member
    Messages: 2,935

    Our 3 kubotas have full under carriage mounts, plows arent just fastened up front.

    I guess your setup would work...maybe the Deere's are built tougher up front I don't know.

    Regardless of my opinion, hope it serves you well and makes you lots of money. :drinkup:
     
  16. JD Dave

    JD Dave PlowSite Fanatic
    Messages: 11,045

    6 and small 7 series Deere's are full framed tractors unlike a Kubota. All of our harness's except our 1 subs all go back to the rear draw bar and I do think that's the best way but it's not really needed in a tractor with frame rails. JMO
     
  17. JohnnyRoyale

    JohnnyRoyale 2000 Club Member
    Messages: 2,935

    I figured that was the case.
     
  18. JD Dave

    JD Dave PlowSite Fanatic
    Messages: 11,045

    No it's a John Deere.;)
     
  19. NSDOT

    NSDOT Senior Member
    Messages: 109

    Nice solid looking plow, I'd maybe use a slotted clevis on the lift chains for easier ajustment, but I'm sure you'll play with lotsa small stuff like that. Good luck!
     
  20. NLS1

    NLS1 Senior Member
    Messages: 315

    Looks like a good machine! Good luck with it. I have no tractor experience, but the hoses are hopefully not in the final location, very vulnerable IMO. Make some money with that beast!