1. Welcome to PlowSite. Notice a fresh look and new features? It’s now easier to share photos and videos, find popular topics fast, and enjoy expanded user profiles. If you have any questions, click HELP at the top or bottom of any page, or send an email to help@plowsite.com. We welcome your feedback.

    Dismiss Notice

new blade vxt

Discussion in 'Equipment, Tools & Vehicle Pictures' started by Livingreen, Dec 3, 2008.

  1. Livingreen

    Livingreen Junior Member
    from Indiana
    Messages: 24

    new vxt blade

    DSCN0518.jpg

    DSCN0517.jpg
     
  2. BMWSTUD25

    BMWSTUD25 Senior Member
    Messages: 630

    Love it!!!
     
  3. nicksplowing

    nicksplowing PlowSite.com Addict
    Messages: 1,226

    nice lookin truck and awesome bladepayup:drinkup:
     
  4. NICHOLS LANDSCA

    NICHOLS LANDSCA PlowSite Veteran
    Messages: 4,302

    Those XT's look inpressive on the front of anything. Looks like it might need an adjustment, looks to be 1" high in the middle.
     
  5. grnstripes

    grnstripes Senior Member
    Messages: 236

    Nice lookin
    Too bad its on a blue oval. JK
    good luck with it
     
  6. Livingreen

    Livingreen Junior Member
    from Indiana
    Messages: 24

    Thanks for the comments. This is my first Boss. I have only had Westerns before now.
     
  7. Chase88

    Chase88 Senior Member
    Messages: 112

    looks good! were you at in indiana?
     
  8. merrimacmill

    merrimacmill PlowSite.com Addict
    from MA
    Messages: 1,822

    I just got my V installed yesterday and its doing the same thing, what can I do about this? What do I adjust?


    Awsome blade by the way!
     
  9. 04superduty

    04superduty PlowSite.com Addict
    Messages: 1,354

    Take the plow off and measure from the center of the hole on the truck side mount to the ground, it should be 15.5". if not you may need to raise the mount.
     
  10. Livingreen

    Livingreen Junior Member
    from Indiana
    Messages: 24

    Chase I am on the westside of Indy. Where are you at?
    As for the adjustment I am taking mine back to have them adjust it. I wish they would have done it right the first time. Oh well it will give me something to do. Were kind of slow right now.
     
  11. DCSpecial

    DCSpecial Senior Member
    from IL
    Messages: 408

    Very nice :D
     
  12. Ford445

    Ford445 Senior Member
    from Vermont
    Messages: 243

    Sweet setup. I love the VXTs. I cant wait 'till spring, when we get all the VXT feedback.

    Good Luck!
     
  13. Oak Hills

    Oak Hills Junior Member
    from mass
    Messages: 19

    nice boss i like those one a lot more then the older ones
     
  14. merrimacmill

    merrimacmill PlowSite.com Addict
    from MA
    Messages: 1,822

    I just measured, and I'm at 14.5". The mount is at its highest point and I don't see any way that there could be room for another mount to get any higher. Should I just crank my T-Bars (which are at stock height) and get that extra inch?


    It just drives me nuts how some of the dealers just don't feel the need to do things right, or atleast inform me of the problem and help with a solution. Now I got to fart around with this issue till its right...
     
    Last edited: Dec 3, 2008
  15. Turbodiesel

    Turbodiesel Senior Member
    Messages: 428

    You'll need to make a minor adjustment to the push beam ..your cutting edge is not flush with the ground.
     
  16. JD Dave

    JD Dave PlowSite Fanatic
    Messages: 11,045

    Crank them like 3 turns and then there is an adjustment bolt at the front of your A Frame, read your manual.
     
  17. merrimacmill

    merrimacmill PlowSite.com Addict
    from MA
    Messages: 1,822

    What is the adjustment bolt for? And your talking about my Boss Owners Manual correct?
     
  18. Turbodiesel

    Turbodiesel Senior Member
    Messages: 428

    Should be 15 1/2 " .
     
  19. f250man

    f250man PlowSite Veteran
    Messages: 3,124

    Very nice rig and plow.
     
  20. Turbodiesel

    Turbodiesel Senior Member
    Messages: 428

    HTML:
    http://service.bossplow.com/Documents/msc04082.pdf
    Page 32

    2-28-08 013.jpg