1. Welcome to PlowSite. Notice a fresh look and new features? It’s now easier to share photos and videos, find popular topics fast, and enjoy expanded user profiles. If you have any questions, click HELP at the top or bottom of any page, or send an email to help@plowsite.com. We welcome your feedback.

    Dismiss Notice

Harness Repair Kit?

Discussion in 'Fisher Engineering Discussion' started by PeteB4, Oct 4, 2014.

  1. PeteB4

    PeteB4 Member
    from Maine
    Messages: 56

    I need a repair harness, and please excuse the lack of knowledge on my part.
    The plow is a MM2. It is a 3-plug. The plow control
    harness needs to be replaced (not the light harness). I had to bullet connect
    them in an emergency at the end of last season. Blue, white and green
    wires. I kept one of the original plugs, and it has 3 pins in it. I need truck
    and plow side repair harnesses. Does the other end have 3 holes???? Would
    you know what I need?? Part Number?

    Thanks!
     
  2. Saber

    Saber Junior Member
    Messages: 21

    There should be a part # on the harness someplace.
     
  3. FordFisherman

    FordFisherman PlowSite.com Addict
    from 06611
    Messages: 1,594

  4. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,975

    If the repair is proper, why replace? But again proper repair
     
  5. Saber

    Saber Junior Member
    Messages: 21

    please post a link to the repair kit, Thanks
     
  6. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,975

    There is no link. It's the way you fixed it. Typical heat shrink but connectors?
     
  7. chevyzrule810

    chevyzrule810 PlowSite.com Addict
    Messages: 1,239

    If you looking to repair the control harness plow side you will need harness #26359.Easiest way to replace this harness is to open up the plastic cover behind the pump to expose the solenoids.Once you have that off take each wire off one at a time from the old harness and plug the new on each terminal one at a time.This will make sure you have each wire on the correct terminal.Put the cover back on.Then remove the ground wire from the negative terminal of the pump motor.Attach the new harness ground wire to the negative terminal of the pump motor.Put some grease on the ground terminal of the pump and on the terminals of the new harness.
     
  8. chevyzrule810

    chevyzrule810 PlowSite.com Addict
    Messages: 1,239

    If you need truck side repair kit you will need #27063.If you want to do both truck and plow repairs you will need #49367K if you have a 12 pin or #49366K if you have a 9 pin.
     
  9. chevyzrule810

    chevyzrule810 PlowSite.com Addict
    Messages: 1,239

  10. PeteB4

    PeteB4 Member
    from Maine
    Messages: 56

    Last edited: Oct 5, 2014
  11. chevyzrule810

    chevyzrule810 PlowSite.com Addict
    Messages: 1,239

    Yes that would be correct.If you notice on the 26359 picture the brown wire has a ring terminal on it.That wire is the ground wire and connects to the negative post on the pump motor.
     
  12. chevyzrule810

    chevyzrule810 PlowSite.com Addict
    Messages: 1,239

    When you replace the truck side make sure you put electrical tape from the plug itself all the way past your repair to keep the elements out of the new repair.
     
  13. PeteB4

    PeteB4 Member
    from Maine
    Messages: 56

    Chevyzrule,

    Thanks for the help! Appreciate it!

    Here's what I have now (done last January).

    Truck Side.JPG

    Plow Side.JPG

    Truck Side.JPG

    Plow Side.JPG
     
  14. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,975

    So that's the trk and plow connector at the grill I'm assuming?
     
  15. PeteB4

    PeteB4 Member
    from Maine
    Messages: 56

    Yes, I just cut both and added bullet connectors. Got me through!
     
  16. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,975

    Ok understand. Then the best is as was said, replace both ends. I wasn't thinking it was at the grill connectors.
     
  17. PeteB4

    PeteB4 Member
    from Maine
    Messages: 56

    Yes, I'll do both. Top pic is truck side. Bottom pic is plow side. I should've labeled the pics.

    Thanks again everyone for all the help!