1. Welcome to PlowSite. Notice a fresh look and new features? It’s now easier to share photos and videos, find popular topics fast, and enjoy expanded user profiles. If you have any questions, click HELP at the top or bottom of any page, or send an email to help@plowsite.com. We welcome your feedback.

    Dismiss Notice

e47h only goes to right

Discussion in 'Meyer / Diamond Products Discussion' started by 992door, Jan 23, 2013.

  1. 992door

    992door Junior Member
    from NC
    Messages: 28

    Only goes to the right no matter what is done no matter which way the switch is turned. If pump is the only thing running still goes right. Need help it is driving me nuts
     
  2. ddobson

    ddobson Junior Member
    from pa
    Messages: 29

    I hate to ask, but did you double check the fluid level in the pump? I had this happen after I flushed/refilled my left/right rams.
     
  3. 992door

    992door Junior Member
    from NC
    Messages: 28

    Yep first thing I checked. OK got the valves out A valve is not closing completely will that cause this
     
    Last edited: Jan 23, 2013
  4. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

    A valve lowers plow, B valves goes up, C goes right. Check your C valve.
     
  5. 992door

    992door Junior Member
    from NC
    Messages: 28

    I can hear C clicking what is the best way to test that one
     
  6. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

    Most likely it is stuck open. Easiest is another valve. You can try using a small allen wrench to push the plunger in the center in. Don't know the exact distance it should move off the top of my head but it is about an 1/8". Also inspect the stem of the valve, these sometime get damaged after hard hit or water freezing. If you have hit something recently you may also want to check the crossover valve but my money is that your C valve is damage.
     
  7. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

    This may help you a bit.
     

    Attached Files:

  8. 992door

    992door Junior Member
    from NC
    Messages: 28

    It moves about 1/32"
     
  9. Jim@esitrucks

    Jim@esitrucks Inactive
    Messages: 1,124

    Check your couplers on the hoses and blocks...left is default on the 47, i.e no valves make it go left
     
  10. 992door

    992door Junior Member
    from NC
    Messages: 28

    ^ I remember seeing that so my thinking is that c is stuck and not able to divert the fluid the way it needs to go to go left. Correct?
     
  11. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

    Or your hoses are backwards. Have you checked for power at the solenoids? to make sure the control is working properly.
     
  12. 992door

    992door Junior Member
    from NC
    Messages: 28

    If you are looking at the motor from the front. Right connection goes to drivers side and the one directly behind the valves goes to passenger. Correct? Have power at all of the solenoids. One of the first things I checked
     
  13. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

  14. 992door

    992door Junior Member
    from NC
    Messages: 28

    Really? OK the people we bought it from had it the other way
     
  15. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686


    Well this means either control/wiring is bad or solenoids are bad or C and B are bad.
     
  16. 992door

    992door Junior Member
    from NC
    Messages: 28

    That narrows it down will figure it out tomorrow
     
  17. racer47

    racer47 Senior Member
    Messages: 330

    b coil bad on last 1 i fixed for guy haveing same problem
     
  18. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

    Bad B coil would only keep it from going up, not keep from up and right.
     
  19. 992door

    992door Junior Member
    from NC
    Messages: 28

    Well I took b out grounded it and put power to it and when it has power it holds the ball to it. When it does not it it releases it
     
  20. kimber750

    kimber750 PlowSite Veteran
    Messages: 3,686

    That just means the coil is working magnetizing the valve. Same thing with B valve as C with small allen wrench, push in to see if plunger moves. Also makes sure all the o-rings are in good condition.