1. Welcome to PlowSite. Notice a fresh look and new features? It’s now easier to share photos and videos, find popular topics fast, and enjoy expanded user profiles. If you have any questions, click HELP at the top or bottom of any page, or send an email to help@plowsite.com. We welcome your feedback.

    Dismiss Notice

Controller Fuse Part Number?

Discussion in 'Western Plows Discussion' started by Whiffyspark, Nov 23, 2013.

  1. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Does anyone have an alternative part number? 5AFB SMD is all I'm finding. I'm hoping I can pick them up at radio shack but I can't find any cross references.

    99% sure the fuse is blown. I have the controller lighting up but it won't turn on. All the pins check out, so i think it shorted.

    Thanks
     
  2. got-h2o

    got-h2o 2000 Club Member
    Messages: 2,439

    It's just a regular glass fuse.
     
  3. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    No this is a 10 pin MVP

    On edit, I switched the two fuses and I still have the exact same issue. Any ideas?
     
  4. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Just realized what you meant, I'm talking about the internal fuses
     
  5. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    Internal of the clicker?
     
  6. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Yes I switched them internal with nochange though
     
  7. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    Well. Look at wiring diag and try and pinpoint what side would be blowing the fuse. Or function I should say
     
  8. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    No fuses are tripped. Controller lights up but won't power on. Have ground on pin nine power on 7. Both sides of relay are good. I'm at a lost
     
  9. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    Is it an ultra or uni setup
     
  10. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Ultra 4 port 3 plug. New controller and harness. Converting from a straight blade
     
  11. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    Plow is hooked up right?
     
  12. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Yup everything's hooked up. I'm about to try moving the solenoid
     
  13. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Cleaned the solenoid mounting place didn't make a difference
     
  14. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    If I jump the terminals it runs but doesn't move that normal?
     
  15. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    No. Your not sending pwr to the plow. Still gotta finger out why. Can you try another clicker
     
  16. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    Its brand new from esi
     
  17. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    So. Try another one
     
  18. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    I don't have a spare $400 controller laying around so I'm going to try swapping modules. If that doesn't work hopefully I can get the controller switched out
     
  19. dieselss

    dieselss PlowSite Fanatic
    Messages: 10,947

    No one has one you can try?
     
  20. Whiffyspark

    Whiffyspark 2000 Club Member
    from SOMD
    Messages: 2,402

    No, no one I know has a round ten pin. All my friends have either straights or MVP+ with the square connectors