Register free!
Search
 
     

Click for Weather
  #1  
Old 01-15-2010, 01:32 PM
johnnysnok's Avatar
johnnysnok johnnysnok is offline
Member
 
Join Date: Dec 2009
Location: South Jersey
Posts: 41
Meyer E-60 C Solenoid seems short

I just replaced my B solenoid and my C solenoid on my E- 60 Meyer pump. My question is the new C solenoid does not completly cover the C cartridge valve nut and there is a small space. The old one completely coverd the valve like the new B soleniod in the picture. Do you think this will be ok with snow,water and salt???
My replacement patrs were #15358 C solenoid and #15381 C cartidge vave.

The new C valve nut is thinker than the old one causing the solenoid to ride high.
Attached Images
     
Reply With Quote
  #2  
Old 01-15-2010, 04:02 PM
AbsoluteH&L's Avatar
AbsoluteH&L AbsoluteH&L is offline
Senior Member
 
Join Date: Jan 2006
Location: Fairport, NY(Rochester)
Posts: 573
I'm wondering about this too. I have the same issue with the new valve I put in. It works fine, but like you said how much crap is going to get in there.
__________________
2005 Ram, to new to plow
2001 F150 7700 7.5' Meyer sold
2001 Cherokee 3" lift 6.5 Meyer
2000 Dakota
Oh sh!t I'm stuck shovel & strap in each truck
You don't have to be big to be successful
Reply With Quote
  #3  
Old 01-15-2010, 05:01 PM
Nasty-Z's Avatar
Nasty-Z Nasty-Z is online now
Senior Member
 
Join Date: Nov 2009
Location: Poconos PA
Posts: 342
It will be fine , the cartridge is sealed.

I would , however , use a slight bit of anti sieze inside the coil to prevent corrosion .

Were these genuine Meyer parts or aftermarket?

15358 is the Cartridge and coil , 15381 is just the cartridge , just wondered why you needed both of those #'s

TOM
__________________
1993 K3500 , Meyer CP9 , Whelen hideaways , some stuff added , some stuff removed

Last edited by Nasty-Z; 01-15-2010 at 05:06 PM.
Reply With Quote
  #4  
Old 01-15-2010, 05:24 PM
johnnysnok's Avatar
johnnysnok johnnysnok is offline
Member
 
Join Date: Dec 2009
Location: South Jersey
Posts: 41
Nasty you may have just answerd my question with your question. After digging in the trash I did not by a seperate C valve and Soleniod i bought a seperate B valve and Soleniod both Meyers which sit correctly. The new C Solenoid assembly the dealer sold me was (SAM) aftermarket #1306055 which replaces Meyer #15358.
So maybe you or someone else can confirm that this is the problem?
I will also call my dealer back to inform him.

PS..I did speak with the Meyer tech on the phone and he said that it should work which it does i just don't want to run into trouble later. I want the real parts.

Thank You
Reply With Quote
  #5  
Old 01-15-2010, 05:27 PM
Nasty-Z's Avatar
Nasty-Z Nasty-Z is online now
Senior Member
 
Join Date: Nov 2009
Location: Poconos PA
Posts: 342
It will be fine , the SAM valves usually sit like that , which is the reason I asked if they were Meyer or aftermarket .

Don't sweat it, antisieze it and go make some $$

TOM
__________________
1993 K3500 , Meyer CP9 , Whelen hideaways , some stuff added , some stuff removed
Reply With Quote
  #6  
Old 02-07-2010, 03:40 PM
tilelayher's Avatar
tilelayher tilelayher is offline
Member
 
Join Date: Nov 2004
Location: SouthEastern PA
Posts: 33
I changed my C coil noth parts the other night it wouldn't come off it took 20 minutes to get the cover off. Thats how bad it was, the new one site like your picture.


Where do you put the antiseize?
Reply With Quote
  #7  
Old 02-07-2010, 03:58 PM
B&B's Avatar
B&B B&B is offline
2000 Club Member
 
Join Date: Nov 2006
Location: GPS says I'm here
Posts: 12,783
Quote:
Originally Posted by tilelayher View Post
I changed my C coil noth parts the other night it wouldn't come off it took 20 minutes to get the cover off. Thats how bad it was, the new one site like your picture.
If the coil was tight on the valve stem then the stem is swelled, which is a very very common issue on the Meyer pumps. So replace the valve too before it begins to cause angle issue. Which it will.
Reply With Quote
  #8  
Old 02-07-2010, 06:31 PM
tilelayher's Avatar
tilelayher tilelayher is offline
Member
 
Join Date: Nov 2004
Location: SouthEastern PA
Posts: 33
Quote:
Originally Posted by B&B View Post
If the coil was tight on the valve stem then the stem is swelled, which is a very very common issue on the Meyer pumps. So replace the valve too before it begins to cause angle issue. Which it will.
I meant both instead of noth yeah I replaced the stem too I have it. It was bent and looked terrible.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©2000 - 2012 PlowSite.comô Moose River Media
All times are GMT -5. The time now is 02:52 PM.

Page generated in 0.02963 seconds with 8 queries