Register free!
Search
 
     

Click for Weather
  #1  
Old 10-31-2000, 07:34 PM
cjtatar cjtatar is offline
Member
 
Join Date: Sep 2000
Location: Endicott, NY
Posts: 32
OK! How's it done? I own a 94 Z71, 4x4, 350V8 1/2 ton, etc. I measured my truck on a flat surface, front sits 1 inches lower than the rear. Then I installed my snow plow, which of course lowered it more. I would like to crank the torsion bars a bit to assist in leveling the truck with only the lower plow frame installed...with the whole plow package installed on the truck, the front is 3 inches lower than the rear. Can anyone help me in cranking the bars? Does a chiltons tell you what to do?
Reply With Quote
  #2  
Old 11-01-2000, 06:01 AM
plowking35 plowking35 is offline
2000 Club Member
 
Join Date: Dec 1999
Location: SE CT
Posts: 2,923
Follow the torsion bar all the way to the back of it. There you will find a jacking bolt. Just turn the jack bolt in till you get the ride height you are looking for.
Dino
Reply With Quote
  #3  
Old 11-01-2000, 06:19 AM
cjtatar cjtatar is offline
Member
 
Join Date: Sep 2000
Location: Endicott, NY
Posts: 32
Should I raise the front end until the tires are off the ground to take any tention off of the torsion bars?
Reply With Quote
  #4  
Old 11-01-2000, 07:31 AM
OBRYANMAINT's Avatar
OBRYANMAINT OBRYANMAINT is offline
PlowSite.com Veteran
 
Join Date: May 2001
Location: ohio
Posts: 531
i cranked up the torsion bars on a chevy to get clearance and it really changed the ride and it will wear on the front end more if i were to be in the same situation again i would adjust the torsion bars just a little bit and then put on some timbren load boosters they work good and will not affect ride

i put these on a 97 in the rear and 1 add a leaf now the truck still rides great and it starts to sag at 2 ton and no sag at all with 1 ton which is the usuall load for me

you can get these for the front to ease your situation
__________________
sima member
Reply With Quote
  #5  
Old 11-01-2000, 04:41 PM
plowking35 plowking35 is offline
2000 Club Member
 
Join Date: Dec 1999
Location: SE CT
Posts: 2,923
Yes I would raise the truck till the tires are off the ground, that will make the jack bolts easier to turn. Also when done, drop the truck back down on level ground, measure from the ground to the middle of the wheelwell, and make sure they measure the same. Adjust to they do.
Dino
Reply With Quote
  #6  
Old 11-01-2000, 05:03 PM
cat320 cat320 is online now
2000 Club Member
 
Join Date: Aug 2000
Location: stoneham,ma
Posts: 2,092
If you adjust the torstion bars will that mess up the alignment ?I put the timbren load boosters on but would like to get it up a little higher but was afraid to touch the bars.
Reply With Quote
  #7  
Old 11-01-2000, 07:59 PM
OBRYANMAINT's Avatar
OBRYANMAINT OBRYANMAINT is offline
PlowSite.com Veteran
 
Join Date: May 2001
Location: ohio
Posts: 531
it will change the alignement but it depends on how much you adjust the bars if it will need to be re-aligned or not the time i adjusted mine all the way up it set it off bad and took it in to be re-aligned but i think a small adjustment in the bars will not matter too much
__________________
sima member
Reply With Quote
  #8  
Old 11-09-2000, 03:52 AM
cjtatar cjtatar is offline
Member
 
Join Date: Sep 2000
Location: Endicott, NY
Posts: 32
To fill you guys in on my status...

This past weekend, I raised the front end, cranked down on the 17mm bolts and waalaa! Truck now sits 1 inch higher, almost level with the rear. Sags by 1/8 inch with no plow frame attached, sits 1/4 inch lower than the rear with plow frame attached. I haven't put the plow on yet, but I suspect it will drop significantly, and that's when I'll want the load improvers (Timbren's?).

Thanks.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
torsion bar keys JTS Landscaping Chevy Truck Discussion 5 10-04-2004 09:31 AM
torsion bar adjustment stanza Chevy Truck Discussion 12 11-14-2003 11:46 PM
torsion bar adjustment stanza Chevy Truck Discussion 16 11-08-2003 07:48 PM
Torsion bar information Joel B. Commercial Snow Removal 12 10-18-2002 12:24 AM
Chevy Torsion bar Adjustment jdjoe_97 Chevy Truck Discussion 10 12-16-2001 06:23 PM





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©2000 - 2012 PlowSite.comô Moose River Media
All times are GMT -5. The time now is 08:26 PM.

Page generated in 0.02896 seconds with 8 queries