Register free!
Search
 
     

Click for Weather
  #1  
Old 12-19-2004, 05:47 PM
john879 john879 is offline
Junior Member
 
Join Date: Dec 2004
Location: crawford, ga 30630
Posts: 1
meyer's e47 snow plow pump wiring diagram

I just purchased a used meyer's snow plow with the 2 toggle switch setup. It also has the E47 pump motor. I am trying to get it all wired up and I am running into a small snag. I have the ground hooked to the battery negative side and I have the power run to the battery and solenoid then down to the motor. I have one white wire that as far as I know hooks up to the small post on the solenoid. I still have no power. I have heard that there is supposed to be a black wire that hooks to 12v key on power. I canno't find this black wire in my harness anywhere. If anyone on here can help me with this or knows where I can get the diagram from I would greatly appreciate it.

Thanks, John-Paul

If you have any info you can email me at john_paul_redden@hotmail.com
Reply With Quote
  #2  
Old 12-19-2004, 08:23 PM
Mebes's Avatar
Mebes Mebes is offline
Senior Member
 
Join Date: Feb 2004
Location: Carver Minnesota
Posts: 386
Use the diamond link at the top of this page to get to the Meyer web page then download the manual.

Or click here http://www.meyerproducts.com/
Reply With Quote
  #3  
Old 12-19-2004, 09:07 PM
Robhollar's Avatar
Robhollar Robhollar is offline
Senior Member
 
Join Date: Dec 2003
Location: Cleveland - Heart of the snow belt
Posts: 773
The black wire that your looking for is going to be under your dash rite off of the plows switch panel. Its what feeds power to the solenoid and coils. It should be fused so look for an in line fuse holder and that could be what your looking for. Also make sure your solenoid has a good ground to it.....Rob
__________________
Full Circle Tree Service
Perry Auto Service
440.725.8439
Reply With Quote
  #4  
Old 12-05-2010, 01:45 PM
joegreen joegreen is offline
Junior Member
 
Join Date: Dec 2010
Location: Mich
Posts: 1
were is the ground on the pump?

Can anyone tell me were the Ground hookup is on the pump?
Reply With Quote
  #5  
Old 12-05-2010, 06:25 PM
geer hed geer hed is offline
Senior Member
 
Join Date: Nov 2010
Location: Pocono Lake, PA
Posts: 251
If your pump is mounted on the truck correctly, the motor will be on the left of the lift cilinder and the valve body will be on the right of the lift cilinder. If it is stand in front of the truck and look down the back of the pump, as your looking down you will see a selenoid with a shield around it. There is a threaded hole to the left if that seleniod, that is where the ground cable goes. You do need a power source to power the controls, and this also is what sends the power to trigger the selenoid. You will want to use a 20 AMP in line fuse on the wire. You can get power for this from several different locations, but what I do is find a spot in the fuse panel that is hot only when the ignition is on. ( otherwise if you accidentaly leave the control switch on the down position it will drain the battery.) This way when the ignition is off so are the controls. When you find which spot in the fuse panel you want to use, pull the fuse and test it to see which side is the feed side, make sure you tap that side of the fuse, otherwise you will blow that fuse when you run the plow, unless it's a 20 AMP or higher fuse.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Snow Plowing? Ole JIM Commercial Snow Removal 23 12-12-2004 02:42 PM
myers E-47 snow plow pump kokomoscalls Commercial Snow Removal 6 12-05-2004 10:57 AM
snow plow wiring chuckf Commercial Snow Removal 4 12-15-2000 09:19 PM
older meyers snow plow justa hick Commercial Snow Removal 3 10-31-2000 07:36 AM





Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright ©2000 - 2012 PlowSite.comô Moose River Media
All times are GMT -5. The time now is 11:27 PM.

Page generated in 0.02579 seconds with 8 queries